ASP-FastBoard - Demo/Support-Forum
Forum anmelden / register Board
SearchSearch CalendarCalendar GalleryGalleryAuction-PortalAuctions GlobalGlobal Top-ListTopMembersMembers StatisticsStats
get your RSS-Feed
Language/Sprache:  Admin  
 Login: ChatChat (0) new User-MapUser-Mapsend Passwordsend Password RegisterRegister

Forum Overview » Homepagetools - Support » Off-Topic » Ceramic foam filter Pore Size
Pages: (1) [1] »
Registration necessaryRegistration necessary
Ceramic foam filter Pore Size
baiyuncarbonno Access no Access first Post cannot be deleted -> delete the whole Topic 
Group: User
Level: treuer Poster


Posts: 214
Joined: 12/13/2021
IP-Address: saved
offline


Refractory Ceramic Foam Filter removes small and suspended non-metallic inclusions in molten aluminum and aluminum alloys, captures the inclusions, and purifies the metal.

Ceramic Foam Filters has many advantages such as good chemical stability, high specific strength, high temperature resistance, thermal shock resistance, large specific surface area, etc., and is widely used in metallurgy, chemical industry, environmental protection and other fields.

In metallurgy, the use of ceramic foam filter plates to remove heterogeneous impurities in the aluminum melt, such as slag, inclusions, etc., is one of the effective methods to purify the aluminum melt.

The slag removal can also reduce the hydrogen content in the aluminum melt; because of its good slag removal effect, simple operation, easy matching with other parts, and low cost, it has become a conventional purification method in the aluminum processing industry.

As the requirements for the quality of aluminum products are getting higher and higher, the requirements for the Ceramic Foam Filter are getting higher and higher.

Selection of Ceramic Foam Filter

Choosing the right filter plate is an important task. The size of the filter plate depends on the flow rate and total amount of the filtered metal. Semi-continuous casting mainly considers the flow rate of metal, while continuous casting mainly considers the total amount of metal.



Selection of Ceramic Foam Filter size

That is, in the effective filtration area, the metal flow rate per square centimeter minute should be 70~210g. When the filtered metal flow rate exceeds this range, the filtration efficiency and the ability to capture debris are drastically reduced. As the pore size of the filter plate decreases, the size of the trapped impurities also decreases, and the efficiency of filtering and removing impurities increases.



Refractory Ceramic Foam Filters Dimension

660x660x50(26 inch)

584x584x50(23 inch)

508x508x50(20 inch)

432x432x50(17 inch)

381x381x50(15 inch)

305x305x50(12 inch)

228x228x50(9 inch)

178x178x50(7 inch)

Ceramic foam filter Pore Size (PPI): 10/20/30/40/50/60

30ppi 40ppi Foundry Filter is the most commonly used ceramic foam filter in the aluminum casting industry.

Ordinary aluminum casting usually uses 10-40ppi ceramic filter plates.

Aviation and high-quality aluminum materials usually use 30-60ppi ceramic filter plates.

Ceramic foam filters are basically divided into 6 pore sizes: 10PPI, 15PPI, 20PPI, 25PPI, 30PPI, and 40PPI. The larger the number, the smaller the aperture. But in actual practice, the four types of 10PPI 20PPI 30PP 40PPI can meet the needs of customers.

Aperture selection

1. The casting: 10~25ppi

2. Semi-continuous casting: 30~60ppi

3. High-quality aluminum or sheet: 50~60ppi

4. Continuous casting and rolling: 50~60p



3/25/2022 7:47:50 AM   
Registration necessaryRegistration necessary
Pages: (1) [1] »
all Times are GMT +1:00
Thread-Info
AccessModerators
Reading: all
Writing: User
Group: general
Cyberlord, sense100
Forum Overview » Homepagetools - Support » Off-Topic » Ceramic foam filter Pore Size

.: Script-Time: 0.141 || SQL-Queries: 6 || Active-Users: 2,196 :.
Powered by ASP-FastBoard HE v0.8, hosted by cyberlord.at